*CLICK HERE* for tips on installation

FRONT TO REAR

REAR TO FRONT

"MEASURING & DIMENSIONING"
for a custom chassis

Below are some examples of body styles and the basic dimensions that we need to custom build a  chassis for your application.

"STOCK TYPE"
similar to OEM

"FRONT TO BACK"
Ladder bar or 4-link type suspensions

"STREET ROD"
stock type

"HOT ROD"
Front to Back
Ladder Bar or 4-link

"STREET ROD Pickup"

"HOT ROD Pickup"

"DIMENSION SPEC SHEET"
**
(A) FRAME HEIGHT (located from front most point on frame to the ground relationship)
***
(B) FRONT TIRE OUTSIDE DIAMETER
***
(C) CENTERLINE OF FRONT AXLE to the front most point of the frame
***
(D) FRAME HEIGHT TO GROUND located from behind front tire
***
(E) FRAME HEIGHT TO GROUND located in front of the rear tire
***
(F) WHEELBASE (axle to axle centerline)
***
(G) REAR FRAME HEIGHT (located at the rear most point of the frame to the ground)
***
(H) REAR TIRE OUTSIDE DIAMETER
***
(I) CENTERLINE OF REAR AXLE to the rear most point of the frame

"TECH TIP!"
When measuring for a custom frame take note. A modern day "UNI-BODY" car (D) and (E) are measured  from the bottom of the rocker panel. Earlier cars and trucks can be measured from the top of the frame  for (D) and (E). If it is just for a "Back-clip" it is best to measure both top and bottom of frame.
***

If you need help or have questions please feel free to contact us.

* FRONT SUSPENSIONS (on this pg.)
* REAR FRAMES (on this pg.)
* SHEETMETAL KITS (on this pg.)

back to top


COILOVER "FEATHERWEIGHT"

Take up to or more than 400# off of your car or truck. Features a jig-welded frame structure with the proper geometry and alignment built in..NO BUMPSTEER. Standard width is 56" hub to hub  measurement. Other widths are made to order.

Features:
* All Tubular A-arms
*Aldan coilovers
*Rack & Pinion Steering
*Mustang II Spindles
*Adjustable height mounts (std)
*Extra Low Stance
*Extra Oil Pan Clearance
*Extra Wide Radiator Clearance (oem)
*Made from 2x3,11ga.wall thickness.
(not inferior .083 wall) using our "No wrinkle technology"

COMPLETE KIT INCLUDES: everything shown above!


Part# 6900..Complete as shown.....$2979.50
Includes: fixture welded frame with adjustable coilover mounts, "Flaming River" rack, tubular A-arms (upper & lower), Aldan coilovers (single adjust), new Mustang II spindles. (very complete!)
***
*UPGRADES are as follows:
QA1 (single adjust)..add...$20.00
QA1 (double adjust)..add...$155.00
***
*NOTE...Standard front clip rails extend back under the floor about 35" from the rear bend.
*Extra long rails running toward rear of car are available for an additional $100
(back to the rear clip)
***
Note: If longer rails are needed, the customer may have to supply a measurement from the spindle  centerline...back to where the frame rails end.
***

INDIVIDUAL PIECES:
* Basic Jig Welded Frame
Part#6901......$1221.24
**
* Lower Tubular Control
Arms W/ Ball Joint
Part#6925......$364.95
**
* Upper A-Arms
Part#6930,#6931...$264.95
**
* Aldan Coilovers
Part#7040......$529.75
***
QA1 coilovers
**QA1 (single adjust) $539.75
**QA1 (double adjust) $699.95
**
* Hardware Package: Bolts,
Tabs, Washers, & Nuts
Part#6942......$34.95

"FEATHERWEIGHT"
INSTALLATION INSTRUCTIONS
( Click Here )


LOWER TUBULAR A-ARMS

--For "featherweight" front clips with coilover shocks.
All a-arms include a ball joint and are powder coated.--

** LOWER CONTROL ARM
Part#6925......$364.95

UPPER TUBULAR A-ARMS

SPECIAL NOTE:
--For "featherweight" front clips with coilover shocks. All a-arms include a ball joint and are powder coated.--

OPTIONS:
* UPPER CONTROL ARM
W/ POLYURETHANE BUSHINGS
Part#6930......$264.95
**
* UPPER CONTROL ARM
W/ SPHERICAL ROD ENDS
Part#6931......$264.95
**
* REPLACEMENT BALL JOINT
FOR UPPER CONTROL ARM
Part#6940......$34.95

CLOSE-UP OF A COILOVER "FEATHERWEIGHT"


"FEATHERWEIGHT" OEM FRONT
END ASSEMBLIES

FEATURES:

* Can take up to or more than 400# off your car!
* Jig welded frame with proper geometry and aligment built in.
* No bumpsteer.
* OEM coil spring type.
* Standard unit has 56" hub to hub measurement.
* Custom width upon order (must call to place special orders!)
* uses OEM Mustang II A-arms,
lower control arms, coil springs, etc.
* Extra low stance.
* Extra oil pan clearance (oil pan removal w/out pulling engine.)
* Extra wide radiator clearance for full width OEM radiators.
**
part #6905.."Featherweight OEM Frame"..$1221.50

"FEATHERWEIGHT" FRONT STRUT ARMS

--New forward design to eliminate the rearward originals on Mustang II front ends. They bolt right on to our OEM featherweight front suspension clips. They can also be used for custom and street rod applications for a smoother ride. Also, our  NEW!! bolt on construction eliminates the need to weld them to the bottom of the OEM control arm!!--

"FEATHERWEIGHT" FRONT STRUT ARMS"
part #6920.....$149.95

*CLICK HERE !!!*
...for our full chassis including the "Featherweight" front suspension!!!

back to top


S-10 REAR FRAMES
**
New S10 truck rear clip Features: mandrel bent "no wrinkle" frame rails made from 2x4x11ga box steel

****
** S-10 4-LINK Pro-Street
clip, w/o housing
Part#3550......$2317.50
**
** S-10 LADDER BAR
clip, w/o housing
Part#3560......$2223.50
**
** 9" Ford housing w/all
suspension mounts welded
(specify ladder bar or 4-link)
add.......$899.00
**
** HOUSING BRACE,
Part#1030A......$110.00
**
** "ALDAN AMERICAN EAGLE" (OR)
"QA1" UPGRADE,
Aldan (single adjust)
Part#7065.......$195.00
Aldan (double adjust)
add.............$320.00
**
QA1 (single adjust)
add.............$215.00
QA1 (double adjust)
add.............$355.00
**
** Upgrade to Chromoly rod
ends (4-LINK ONLY),
Part#3020.......$150.00
**
** FILL AND DRAIN
Part#1005...$68.00
****
Fixture welded "4-Link"
frame only, w/all mounts
Part#3555........$1592.95
***
Welded "Ladder Bar"
frame only, w/all mounts
Part#3565.......$1545.75

*NEW... S10 kits features: Mandrel
Bent 2x4x11ga. Frame Rails
This is the easiest to install on the market!!
"SLIDE-IN-AND-WELD"

**FEATURES**
* THE BEST & EASIEST ON THE MARKET!
* Jig welded heavy duty frame
* Low profile 4-link or ladder bars
* Series 7000 coilovers
* Panhard track locator
* All poly rod ends (R&L)
* Very COMPLETE!!
***
**Example of our Ladder Bar frame..(shown below!)
"OTHER DESIGNS AVAILABLE"


(above)
Fixture welded "Ladder Bar" rear frame w/mounts
Part#3565.......$1545.75
***

This NEW 4-link rear frame accepts all of our  "Competition 4-link" components. It allows for a very low stance like a Pro-stock.
--------------
***
As shown above includes:
Fixture welded frame, HD 4-link,
Aldan single adjust coilovers,
wishbone trac-locator, 9" Ford
housing, hardware....$4086.50
Moser axles...$370
BSR package...$99
Double adjust coilovers also available.
***
It is made using our 2x3 rails. It features the same easy installation as our typical S10 rear clip...(slide in and weld). Some of the flooring will need to be removed when installing.
***
Rear crossmember with box/body holes (same as on our standard kits). These holes allow for easier box
mounting.
**
"Competition 4-link"
Fixture welded frame only.
Part#3568.......$1427.95
Oval crossmember option $150 additional
(SHOWN BELOW)

***
* For "S10" full chassis
CLICK HERE!!*
***

*NEW*
**S10 Wheel Tubs**
The perfect solution when building a "Pro-Street" or "Drag" S10. These "NEW" tubs are designed to  replace the entire "inner" wheel house , instead of splitting the "OEM" wheel house and widening it.  They are made extra wide and are adjustable for the desired fit.
***
Part #4090...S10 tub...steel...$149.95

LUV PICKUP
Rear Frame Clip
Includes: Jig welded frame,"Low Profile" pro-street 4-link, series 7000 coilovers, panhard track locator, rod ends.
Very complete!
Part #3570......$2170.00
**
NEW! Fixture welded 9" Ford housing
with all brackets located...add..$899.00
**
Moser race axles
(up to 35 splines)....$370.00
Bearings,1/2x3 studs, retainers
add...................$99.00

back to top

SHEET METAL FLOOR KITS


Ladder Bar and 4-Link
*ladder bar shown*

FEATURES:
* Aluminum(.032) or, Steel(22ga) available
* Designed for Ladder bar, Competition 4-link, or Ultimate II
* Typically ordered with jig welded frame assembly
* All panels for complete floor installation
* Backup parts and Rivets
* Panels already beadrolled for strength and beauty

OPTIONS:
** ALUMINUM SHEETMETAL KIT
FOR LADDER BAR
Part#4000......$349.95
**
** STEEL SHEETMETAL KIT
FOR LADDER BAR
Part#4001......$329.95
**
** ALUMINUM SHEETMETAL KIT
FOR 4-LINK (PRO STREET)
Part#4002......$349.95
**
** STEEL SHEETMETAL KIT
FOR 4-LINK (PRO STREET)
Part#4003......$329.95
**
** ALUMINUM SHEETMETAL KIT
FOR 4-LINK (COMPETITION)
Part#4004......$349.95
**
** STEEL SHEETMETAL KIT
FOR 4-LINK (COMPETITION)
Part#4005......$329.95

"COMPETITION 4-LINK" FLOOR KIT

"PRO-STREET 4-LINK" FLOOR KIT


REAR CLIPS

REAR ASSEMBLIES

STEERING ITEMS

WHEEL TUBS

MISC. HARDWARE

FACTORY SHAPED
FRAMES &
FRAMES BENT
TO SPEC !!